TILED STAIR RISERS FREE

Its submitted by admin in the best field. We identified it from well-behaved source. Here are a number of highest rated Tile Stair Risers pictures upon internet. Wait a week and apply grout sealer to protect against stains.Tile Stair Risers. When the tiles are completely dry give them a final polish with a cotton cloth. To remove simply wipe with your grout sponge again. As you work you may notice a hazy film as group residue dries on the tiles. Then after checking manufacturer’s instructions for dry time use a large damp sponge to clean tile surfaces. Let the grout dry while you work on the next riser. Then smear on to the tiles working it into the joints and scraping if off the tile surface. Use your trowel to transfer grout to a rubber-faced float. When you’re ready, mix grout according to instructions using a drill with a paddle attachment. Before applying grout let the mastic dry according to manufacturer’s instructions. Then move down the staircase tiling each riser the same way. Lightly tap each tile with a rubber mallet to help secure them in place. You want to flatten the mastic ridges, not squeeze the mastic out. Wiggle the tile or sheet up and down while applying light pressure. Place the first end tile or sheet of tiles on the mastic. Holding the applicator at a 45 degree angle drag the notched edge across the riser to make horizontal ridges. Apply mastic with a notched trowel or plastic applicator to the riser in an even 1/4 inch layer. If you need to cut your tiles use tile nippers to trim them.Īpply mastic. Butt the last sheet into the opposing wall and mark where it needs to be cut. Just cut them to the correct height and butt the first sheet to the wall. If you’re using small tiles attached to a mesh backing you may only need to use a utility knife to cut sheets to fit. Measure the width and height of the riser you’re working on. Then tape sheets of paper to the treads to protect them while you tile.Ĭut mesh-backed tiles.

Use a vacuum and microfiber cloth to remove dust. Keep in mind that you’re not trying to remove paint or finish. Scrape off any lose paint then lightly scuff with 80 grit sandpaper wrapped around a sanding block.

Once your treads are dry you’ll start working on the risers. Let dry according to manufacturer’s instructions before moving on to the next step. Use a disposable foam brush to apply your stain, wiping off excess as you go with a cotton cloth. If you decide to stain your steps start by taping off the areas where the treads meet the wall.

TILED STAIR RISERS FREE

But feel free to leave the treads natural if you’d like. If you plan on staining your steps you’ll do it now. Vacuum and wipe clean with a microfiber cloth. Sand one more time with 100 grit sandpaper. Vacuum the treads again then carefully inspect the surface to ensure you’ve removed any ridges from the belt sander. Then also using 80 grit sandpaper smooth any areas you can’t reach with a sanding block or a Mouse® detail sander. This time with 80 grit sandpaper on a quarter sheet sander. Work your way around the outside of each tread with a random Orbit sander, Quarter Sheet sander, and Mouse® Detail sander, all equipped with 60 grit sandpaper then vacuum the treads.įinish sand treads. Wrap a piece of 60 grit sandpaper around a sanding block to smooth the round surface of the tread and remove the finish. Sand with the grain along the length of each tread being careful not to bump the sander into the walls. Using a belt sander start with 60 grit sandpaper.

Refinishing your treads starts with a rough sanding. When taking on this DIY task, be sure to equip yourself with the proper safety gear.

Stone Sealer (If Using Individual Tiles).

Score-And-Snap Tile Cutter (If Using Individual Tiles).

Scoring Wheel & Nipper (If Using Mesh0Backed Tile).

Here’s what you’ll need to take on this project: Tiling stair risers and refinishing the treads is something you could do on your own over a single weekend and will give your stairs a fresh new look. Over time tread finish may wear away and vertical riser boards can get dented and scuffed.

Tiled stair risers